产品简介 / PRODUCT INTRODUCTION
The high performance acrylic emulsion and silicone rubber emulsion are mainly based on the high performance acrylic emulsion and silicone rubber emulsion. The coating product is a water based single component waterproof coating, and the waterproof layer formed by the waterproof layer has strong anti seepage force, good waterproof effect and long service life.
产品特点 / PRODUCTION CHARACTERISTICS
1 has a unique waterproof, high flexibility and integrity, the film has no continuous joints;2 high temperature resistance, low temperature resistance, good aging resistance;3 on cement mort-ar, concrete matrix, wood, ceramics, glass and other building materials have a good bond, per-meability;4 extension rate is good, anti ultraviolet ability is excellent;5 nontoxic, tasteless, non polluting, green environmental protection;6 color to beautify the environment;7 one component, water soluble, roll coating, spraying can be;8 safe, reliable, easy to operate, construction is convenient, shorten the time limit for a project.
适用范围 / SCOPE OF APPLICATION
1 for the new old roof, roof, tile roof (three bent tile roof), metal roof and planting roof waterproof engineering;2 for grain depot, warehouse, building waterproof Engineering3 used in bridges, tunnels, civil air defense proj-ects, etc.;4 for swimming pools, ponds, reservoirs, sewage treatment pond waterproof engineering;5 used for facade and new wall, waterproof, waterproof engineering;6 waterproof for special and complex projects.
施工程序 / CONSTRUCTION PROCEDURE
Grassroots acceptance and cleaning. Coating construction of the basic level should be flat, smooth, solid,. When the foundation sand, peeling, pits, cracks, uneven phenomenon, should be treated to meet the acceptance criteria can be used only for the construction of waterproof layer. Cleaning base remaining debris, with a broom or hair dryer blowing on the basal surface shall not have dust, grease. Brushing base treatment agent. Base treatment in accordance with the high elastic acrylic rubber waterproof paint: clean water mixing ratio of =1:2, using the weight of approximately 0.2kg/ square meters. The basic treatment agent evenly coated in the waterproof layer construction. Brushing primer s-hould be uniform and thoughtful, do not show, do not pile up. After the drying process (about 1H) can be carried out in the next process of construction.1 before the construction of the waterproof paint mixing uniform, the use of water can not be free (to do the basic treatment agent except).2 this product uses the method of brushing or rolling coating construction, the direction of the painting, the length of the trip should be consistent, all over the brush should be carried out alternately, brushing should be uniform. Waterproof coating should be layered coating.3 every time should be before the dry again a-fter brushing (hand touch coating is not sticky hand is appropriate).4 four with a cloth laying process (casing cloth glass cloth, polyester cloth), joint is not less than 5cm. The laying of matrix in the coating material should be enhanced, while coated side Pu matrix cloth, carcass should be scraping bubble discharge, the paint soaked body and cover completely, there shall be no matrix exposure phenomenon.
注意事项 / MATTERS NEEDING ATTENTION
1 the construction temperature should be above 5 degrees, 35 degrees below the constructi-
on, prohibit the construction of rain and snow.2 when the use of paint can not be any water. Do
basic treatment agents except.3 brushing before mixing, brushing after 3 hours should not be
irrigated.4 with a sealed barrel, storage temperature should not be less than 0 degrees Celsi-
us, storage period of 12 months or more. This product is non-toxic, non flammable, non corr-
osive, can be transported by ordinary goods.
贮存方法 / STORAGE METHOD
The product should be placed in a cool, ventilated, dry place and save for two years in sealed
condition. No abnormal that the product was beyond the guarantee period can still use.
参考用量 / REFERENCE DOSAGE
A flat datum is 1-1.5kg/㎡
执行标准 / EXECUTIVE STANDARD
产品包 装 / PACKING OF PRODUCT